IC-7300MK2

The IC-7300MK2 is the much-anticipated successor to the wildly successful and world-renowned IC-7300. Building on a legacy of excellence, the IC-7300MK2 sets a new standard for HF operation. With dramatically enhanced performance, including superior RMDR, lower phase noise and the addition of features such as an HDMI port and a built-in CW decoder, this transceiver is set to redefine your time on the air.

Enhanced Features

Improved RMDR and Phase Noise Characteristics
The IC-7300MK2’s RMDR is improved to about 12 dB* typical (at 2 kHz separation) and transmit Phase Noise characteristics are improved by about 12 dB (at 1 kHz separation) compared to the previous model. The superior Phase Noise characteristics reduce noise components in both receive and transmit signals.
* 2 kHz separation at 14.2 MHz, CW, IF BW: 500 Hz

What is RMDR: RMDR (Reciprocal Mixing Dynamic Range) is a key indicator of how much a receiver’s sensitivity is degraded by strong nearby signals. A higher RMDR value means less desensitisation from adjacent signals. Generally, lower LO phase noise yields better RMDR performance.

Power Saving and Lower Heat Generation for Longer Continuous Operation
Through component selection and DC power optimisation, the IC-7300MK2 reduces heat generation and enables stable operation during extended operating periods such as contest operation. Compared to the previous model, the IC-7300MK2 reduces power consumption from 0.9 A to 0.7 A (typical) during RX standby. Furthermore, the fan control has been improved, making fan noise much less noticeable.

New Features

HDMI Port for External Display
As a first for Icom’s HF/50 MHz radios, the IC-7300MK2 incorporates an HDMI™ port for external display connection. Operating information such as frequency, scope, waterfall and menus can be shown on a large monitor and audio can also be output through HDMI™ to the display’s speakers.

RX-ANT Connectors for BPF, Preamps and Receiving Antennas
The RX Antenna IN/OUT connectors enable you to take advantage of antenna characteristics for optimised reception such as avoiding interference and QRN. External bandpass filters and preamps can also be connected to these connectors.

Simplified Remote Control Using RS-BA1
Whether from a remote location within your home QTH or from somewhere around the world the RS-BA1 (Version 2) software enables you to operate your IC-7300MK2*. With the addition of an Ethernet connector, a base station computer is not required. Not only can you control the radio settings and display a spectrum scope with the waterfall, but you can also remotely turn the radio on or off through the Internet.
* RTTY and CW decode functions are not supported in the RS-BA1 Control Software.

Built-in CW Decoder
Another first for Icom’s HF/50 MHz radio, the IC-7300MK2 can decode Morse code signals without using a PC or other external equipment*. The decode settings can be customised to suit various situations and needs, including decode key speed (AUTO, LOCK, KEYSPEED linked), decode filter (AUTO, FIX, OFF), and threshold (AUTO, MANUAL).
* Decoding accuracy may vary depending on receiving conditions.

USB Type-C™ with Dual COM + Audio
The IC-7300MK2 features a USB Type-C port with dual virtual COM ports and audio input/Output capabilities. You can use two applications simultaneously, such as FT8, logging and contest software, with just one USB cable.
* CW decode output to the USB port is not supported.

APF (Audio Peak Filter) for CW Signals
The APF improves CW reception by emphasising a specific audio frequency making it easier to zero in on a desired signal. The APF level is adjustable from 0 to 6 dB in 1 dB steps.

Main Features

Real-Time Spectrum Scope
Equipped with a real-time spectrum scope, the IC-7300MK2 delivers sophisticated operation through intuitive touch control featuring advanced specifications such as resolution, sweep speed, and dynamic range. While listening to received audio, you can check for clear frequencies, monitor band conditions and quickly access target signals with simple touch operation.

High-Resolution Waterfall Function
The combination of the waterfall function and the real-time spectrum scope assists in maximum receive performance of the IC-7300MK2 and increases QSO opportunities without missing weak signals. The waterfall function shows a change of signal strength over a period and allows you to find weak signals that may not be apparent on the spectrum scope.

Audio Scope Function
The audio scope function can be used to observe various AF characteristics such as microphone compressor level, filter width, notch filter width and keying waveform in the CW mode. Either the transmit or receive audio can be displayed on the FFT scope with the waterfall function and the oscilloscope.

Automatic Contest Serial Numbering
This function is powerful in CW and RTTY contests. Each time the pre-programmed memory is transmitted, the serial number is automatically counted from 001. The serial number can be set in multiple locations to ensure that the contest number is reliably copied.

Advanced RF Direct Sampling
The IC-7300MK2 utilises RF direct sampling technology that directly converts RF signals to digital data and processes them within an advanced Field-Programmable Gate Array (FPGA). This innovative approach dramatically simplifies circuit architecture while delivering exceptional performance that sets new standards in Amateur radio.

Advanced “IP+” Technology
The “IP+” function significantly enhances intermodulation distortion (IMD) performance. When you receive strong interference adjacent to your intended signal, it intelligently optimises the AD converter to minimise signal distortion and ensure clean reception.

15 High-Performance Discrete Bandpass Filters
Incorporating 15 discrete RF bandpass filters with high-Q factor coils, the IC-7300MK2 delivers exceptional out-of-band interference suppression, comparable to premium-class transceivers.

Built-in Automatic Antenna Tuner
A built-in automatic antenna tuner recalls optimal settings in its memory for rapid band switching. The Enforced Tuning function* enables operation with a wide range of non-resonant antennas, providing emergency communication capability.
* Do not use the Enforced Tuning function except in case of an emergency. Transmission power may be reduced.

Multi-Dial Knob for Enhanced Operation
The intuitive combination of a multi-dial knob and touchscreen delivers fast, efficient control. Press the multi-dial knob to display the menu on the right side of the screen, touch to select your desired function, then rotate the knob for adjustment.

Large Touch Screen Colour TFT LCD
The large 4.3-inch colour TFT touch LCD offers intuitive operation. Using the software keypad of the touch screen, you can easily set various functions and edit memory contents.

One-Touch FT8 Mode Preset
Experience simplified FT8 operation with one-touch preset switching. Select [FT8] from the preset menu to automatically configure all necessary settings or choose [Normal] to instantly return to conventional operation. Presets 3 to 5 are user-programmable, ensuring compatibility with future digital modes.

Superior Sound Quality
A high-performance speaker unit with a large magnet is housed in a dedicated acoustic space, providing exceptional clarity and minimal distortion at any volume.

SD Memory Card Slot for Data Storage
The IC-7300MK2 stores various data on SD cards, including communication recordings, voice memories, RTTY decode logs, and screen captures. Personal settings can also be saved, enabling instant configuration switching between operators with a simple card exchange.

Other Features

• Large and efficient cooling fan.
• Multi-function meter (Po, SWR, ALC, COMP, VD and ID).
• 101 memory channels (99 regular, two scan edges).
• CW functions: Full break-in, CW reverse, CW auto tuning.

Supplied accessories:

• HM-219 Hand microphone • DC power cable • Fuses • Plugs